Author | Message |
---|
Techno100
Posts : 1738 Join date : 2012-11-15 Location : Leeds
| Subject: Re: Bon Voyage Techno! Fri 14 Jun 2013 - 18:12 | |
| We stocked up on the wines that we scored highest after last years selection. The two top choices had only gone up a couple of cents each. We bought 120 biere 33 export, 48 bottles of 1664 blonde, 18 bottles of frexnet, 72 bottles of red, 2 monkey shoulder | |
|
| |
The Burchies
Posts : 3981 Join date : 2012-11-15 Age : 111 Location : Bournemouth
| Subject: Re: Bon Voyage Techno! Fri 14 Jun 2013 - 22:47 | |
| That'll keep you going until we see you over there in September | |
|
| |
mike 100
Posts : 1471 Join date : 2013-03-07 Age : 66 Location : in my van/or reading paper on lav
| Subject: Re: Bon Voyage Techno! Sat 15 Jun 2013 - 7:35 | |
| morning andy jac,s hope enjoying your trip and all well when are you back | |
|
| |
Techno100
Posts : 1738 Join date : 2012-11-15 Location : Leeds
| Subject: Re: Bon Voyage Techno! Sat 15 Jun 2013 - 10:46 | |
| On the A1 now after big diversion off the A14 due to roadworks :-( | |
|
| |
Techno100
Posts : 1738 Join date : 2012-11-15 Location : Leeds
| Subject: Re: Bon Voyage Techno! Sat 15 Jun 2013 - 20:35 | |
| Home OK before 2 this aft, managed to empty the van in two trips. Birmingham job is replaced with a 9 day shop refurb in Glasgow train station. The van performed faultlessly throughout and I'm real glad I have Michelin camper tyres with side wall reinforcement as I hit a good share of curbs. The electrics could have fed 4 vans but the inverter battery cables are not big enough IMHO so I've uprated them to 35mm. I experienced one afternoon where the passenger side suspension made a lot of squealing when steering around roundabouts but the next day it had gone? Just need to acquire the knowledge of suitable repair materials for the rear corner moulding to set him straight. | |
|
| |
Techno100
Posts : 1738 Join date : 2012-11-15 Location : Leeds
| Subject: Re: Bon Voyage Techno! Sat 15 Jun 2013 - 20:36 | |
| Next trip! The Northern show | |
|
| |
The author of this message was banned from the forum - See the message |
grandadbaza
Posts : 1986 Join date : 2012-11-15
| Subject: Re: Bon Voyage Techno! Sat 15 Jun 2013 - 20:44 | |
| - Techno100 wrote:
- Home OK before 2 this aft, managed to empty the van in two trips.
Birmingham job is replaced with a 9 day shop refurb in Glasgow train station. The van performed faultlessly throughout and I'm real glad I have Michelin camper tyres with side wall reinforcement as I hit a good share of curbs. The electrics could have fed 4 vans but the inverter battery cables are not big enough IMHO so I've uprated them to 35mm. I experienced one afternoon where the passenger side suspension made a lot of squealing when steering around roundabouts but the next day it had gone? Just need to acquire the knowledge of suitable repair materials for the rear corner moulding to set him straight
When we were in France , a couple of times we heard a some strange noises from the rear of the van , then they went away , a few days later we broke down, so it may be prudent to get underneath and check out where your noise was coming from? | |
|
| |
Techno100
Posts : 1738 Join date : 2012-11-15 Location : Leeds
| Subject: Re: Bon Voyage Techno! Sat 15 Jun 2013 - 20:46 | |
| Yes too true Baz. I had a look but nothing obvious. At Fecamp that afternoon it would squeal while turning the steering while stationary which was quite alarming but it's gone completely. | |
|
| |
The Burchies
Posts : 3981 Join date : 2012-11-15 Age : 111 Location : Bournemouth
| Subject: Re: Bon Voyage Techno! Sun 16 Jun 2013 - 10:40 | |
| Glad to see you made it back safely, sounds like you both enjoyed yourselves? | |
|
| |
mike 100
Posts : 1471 Join date : 2013-03-07 Age : 66 Location : in my van/or reading paper on lav
| Subject: Re: Bon Voyage Techno! Sun 16 Jun 2013 - 11:01 | |
| andy we had noise from front off side turned out to be bits of rust on edged of brake disc cleaned of now ok horrible noise ok now hope this helps mike | |
|
| |
Techno100
Posts : 1738 Join date : 2012-11-15 Location : Leeds
| Subject: Re: Bon Voyage Techno! Sun 16 Jun 2013 - 15:04 | |
| Thanks Mike but that's not it. Having fitted new brake pads I'm aware of that noise as the pads bed in to worn discs. On cornering the very tiny amount of wheel bearing float allows the new pads to clip the rust on the disc edge.Mine are fully bedded in now and it no longer happens for now. The noise I got was even without the wheels rotating, just steering on the spot could do it. | |
|
| |
The Burchies
Posts : 3981 Join date : 2012-11-15 Age : 111 Location : Bournemouth
| Subject: Re: Bon Voyage Techno! Sun 16 Jun 2013 - 17:14 | |
| Might be noise from power steering belt??? | |
|
| |
Techno100
Posts : 1738 Join date : 2012-11-15 Location : Leeds
| Subject: Re: Bon Voyage Techno! Sun 16 Jun 2013 - 17:37 | |
| Thanks Mark but I believe the Fiat pump is direct driven (no belt) | |
|
| |
Techno100
Posts : 1738 Join date : 2012-11-15 Location : Leeds
| Subject: Re: Bon Voyage Techno! Sun 16 Jun 2013 - 18:15 | |
| | |
|
| |
Techno100
Posts : 1738 Join date : 2012-11-15 Location : Leeds
| Subject: Re: Bon Voyage Techno! Mon 17 Jun 2013 - 15:49 | |
| Got it for £100 inc delivery. Now just need both corners spraying to match each other. | |
|
| |
Sponsored content
| Subject: Re: Bon Voyage Techno! | |
| |
|
| |
| Bon Voyage Techno! | |
|